Revolution Industrial Equipment Co.
  • Home
  • Products
    • New Equipment
    • Rat Vac
    • Vacuum Pumps and Blowers
    • Power Up Lubricants
    • Sewer Equipment
    • Hydrovac Parts
    • Hoses and Fittings
    • Valves
    • Chemicals
    • Used Inventory
  • Catalogues
  • Product Videos
  • Contact (306) 539-8775
  • Schellvac

USED INVENTORY


​

2003 International 7400 Flusher Unit

Picture
Picture
Picture
Picture
Picture
This unit has been exceptionally well maintained. The Roots blower was rebuilt under 2 years ago and has not been run very much since. The water pump was rebuilt approx. 5 years ago. 
The CVIP expired in March.
Holds approx. 4 cubes of water. 80 GPM pump
This unit is priced to sell!!!
​Call (306) 539-8775 for more information!

2015 Ring-O-Matic 850 Vac EX on 2015 Hino Chassis

Picture
Picture
Picture
​800 gallon spoils tank, 50Hp CAT industrial diesel, 1000 CFM Displacement Gardner Denver blower, Pressurized Tank Offload, Pressure Filter Backflush, Reverse Flow Suction Hose Blow-Out, 2x100 gallon poly fresh water tanks, 6.0 gpm @ 4000psi Water Pump, premium silencer package, hydraulic tank hoist, hydraulic full opening rear door, sight-glass for level detection, 50' x 3" suction hose, 50' x 3/8" high pressure hose reel, wash gun,  5' pothole lance, 6' suction tube with lawnsweep, safety strobe and dual LED worklights; Includes, In tank washer, 4" hose intake upgrade, 3" decant valve, water pressure control.
Chassis - 2015 Hino w/ Air Ride Suspension 15,000 kms
450 hrs on the vac unit.

This unit has served the customer very well and he is looking to upgrade the unit. It is priced to sell! Call (306) 539-8775 for details.
Picture

2002 Freightliner Septic Truck

Picture
Picture
2002 Freightliner Chassis
Septic body 10 years approximate. Has not been used very much.
Mercedes engine fresh rebuild, new clutch under 5000kms. Starts and runs like a dream. These Mercedes are very good on fuel.
2800 gal tank
Fruitland 500 Vacuum Pump
Full hoist 
Vibrator
Full opening rear door.
Rubber at 85%
This unit is in exceptional mechanical condition just shows its age a little.
Call (306) 539-8775 for pricing!
2008 Ram Vac HX-6
Picture
Chassis - Sterling
This unit is in good repair w/good rubber.
Has optional air excavation system. 
Low PTO hours.

64,000 KMS

This unit needs to move! Owner is motivated! Call for pricing.

​Call (306) 539-8775 or (306) 543-8775 for pricing


2018 Kenworth, T-880
(NEW UNIT)​

Picture

Chassis
2018 Kenworth, T-880 450 HP, Automatic, Tandem axle, 66,000 GVWR

Tank Capacity
3600 USG + 3% Outage

Hydrostatic Test Pressure
40.0 PSIG

Internal Design Pressure
25PSIG MAWP

External Design Pressure
15PSIG

Standards
Meet all requirements

Section VIII Division 1 ASME Boiler and Pressure Vessel Code

National Board Registered

Tanks to be designed and Constructed

Department of Transportation Specifications DOT 407/12

Head Material
0.3125 SA516-70

Shell Material
0.3125 SA516-70

Tank Diameter
78" OD

Operating Temperature
-20 to 200 degrees F

Pressure Relief
4" SS Girard pressure vent, 30 PSIG setting mounted top of tank

Primary Shut-off
8” internal shut-off with 12" stainless steel float ball/cage assembly and 8" rubber seat.

Baffle
One anti surge baffle mounted on reinforcing pads

Rings
Circumferential reinforcement rings with tank support feet where applicable

Overturn Protection
Front, center and rear 4" pipe construction overturns with reinforcement pads and gussets; cw overturn rings

Manway
20" diameter located top of tank.

Liquid Level Indicator
Stainless Steel construction rotary float gauge with 6” float ball assembly located on front driver side with grab handle and up position tie back

Rear Door
Hydraulic full opening rear door assembly with 6 heavy duty wing clamps, neoprene rubber rear door gasket, double acting hydraulic cylinder and safety brace.

Suction Valve
6" ANSI Betts air open/spring close valve and actuator, 6" stand pipe/deflector plate assembly, aluminum Kamlok fittings mounted on rear head at 4 o'clock position…VALVE WILL BE HEATED

Discharge Valve
6" ANSI Betts air open/spring close valve and actuator with aluminum Kamlok fittings mounted on bottom center of rear door…VALVE WILL BE HEATED

Isolation Valve
8” air operated butterfly valve between primary and cyclone with manual air switch control.

Filtration System
Dual 20" diameter cyclones mounted on 20" diameter drop box with side swing clean out, 3" brass drain valve and aluminum Kamlok fittings, Cusco 30” diameter final filter assembly installed for protection of blower with 20” diameter stainless core steel  with100 micron filter.

Silencers
12" intake and exhaust silencers.

Blower Specifications
Roots DVJ 721 Blower 3658 CFM free air rating, 2850CFM @ 18"Hg, 27"Hg maximum vacuum

Blower Piping
Single 8" diameter with 8" quick disconnect rubber boot assembly

Blower Valving
6" manual butterfly vacuum relief valve and 10" inline check valve assembly

Drive
Driven from air shift transfer case.

Pressure Unloading System
Moro PM80 air cooled vacuum/pressure pump (350 CFM free air 28" Hg) hydraulically driven with 3" air operated isolation butterfly valve, 3" diameter no disconnect piping, 3" secondary moisture trap filter and muffler/oil trap assembly.

Hydraulic Reservoir
Mounted on hydraulic dump sub-frame with suction strainer, diffuser, fill cap, hydraulic oil filters and sight glass.

Hydraulic Dump System
Full length hydraulic dump sub-frame with 20 ton, 3 stage single acting dump cylinder, rear dump pivot assembly and safety brace.

Vibrator
Hydraulic vibrator assembly mounted bottom of tank with reinforcing pad, heavy duty mounting channel and pressure relief valve

Hydraulic Controls
3-spool valve body for control of pressure unloading system/vibrator, rear door and hydraulic dump complete with Hydraulic pressure guage. Controls to be located on the driver side of unit near control panel.

Gauges
Turbovac gauge panel assembly with tank vacuum/pressure gauge, filter element vacuum gauges, tachometer, throttle control and 3” isolation valve control.  Panel to be lighted for night operation.  Panel to be located on the driver side of unit near hydraulic controls.

Side Trays
Full-length side boxes for hose storage / fender assembly with anti-sail mud-flaps and rear tire skirt.

Trim
Ladder Assembly mounted on the driver side of the tank c/w sidebox ladder.

(4) Numbered Placards

50' static line

Steel toolbox assembly 36" wide x 18" deep x 18" high

Lighting
DOT LED moisture proof lighting conformant to FMVSS 108

(3) lamp rear module assembly

Clearance lamps

Reflectors

(3) in a row clearance markers

(2) rear Halogen Flood lights and (1) at controls

(1) rear amber strobe beacon

Bumper
DOT rear bumper for protection of external valves with platform/step assembly and rear dirt shield.

Painting
Sections of tank and the entire body of the rest of the unit (non-tank) shall be sandblasted and primed with two (2) coats of primer and painted with two (2) coats of single stage Axalta paint. 

Dual Hose Hooks
Dual rear mounted hose hooks


Call for pricing. (306) 539-8775


Contact us for more information

Exceptional products for exceptional customers


Contact

306-539-8775
revolutionequipment@sasktel.net

What people are saying...

"I have been using your rotating nozzles for a while. In the past we had used pressure washer style turbo nozzles – there’s just no comparison to your Ripsaw. The other ones were simply that, just pressure washer nozzles, not something designed for hydro excavation."
- Steve Rogers, Owner, Rogers HydroVac Service
Picture
Copyright © 2015-2016 Revolution Industrial Equipment Co. 
  • Home
  • Products
    • New Equipment
    • Rat Vac
    • Vacuum Pumps and Blowers
    • Power Up Lubricants
    • Sewer Equipment
    • Hydrovac Parts
    • Hoses and Fittings
    • Valves
    • Chemicals
    • Used Inventory
  • Catalogues
  • Product Videos
  • Contact (306) 539-8775
  • Schellvac